Specifications

Product Code PM110
USB Power Delivery Tester
PM125
USB Power Delivery Tester with PPS and QC
CPU: ARM Cortex M0 ARM Cortex M0
Memory: 16KB RAM, 128K Flash 16KB RAM, 128K Flash
User Interface: 1.8" LCD 128X64 Pixels + Rotary dial 1.8" LCD 128X64 Pixels + Rotary dial
USB standards: USB Power Delivery Specification Revision 3.0, and Battery Charging Specification Revision 1.2 USB Power Delivery Specification Revision 3.0, Battery Charging Specification Revision 1.2 and Quick Charge 4 (including QC1, QC2, QC3, QC4 and QC4+)
Port Detection: DCP, SDP, CDP, Type-C (non-PD, fixed profile), Proprietary Chargers DCP, SDP, CDP, Type-C (non-PD, fixed profile and PPS), QC and Proprietary Chargers
Physical connectors: USB A, USB B, USB Type-C USB A, USB B, USB Type-C
Maximum Load: 60W Continuous, 100W for 5 Minutes 60W Continuous, 100W for 5 Minutes
Cooling: Heatsink with two fans Heatsink with two fans
Current Adjustment: Yes Yes
Voltage Adjustment for PPS/QC profiles: No Yes
Operational Voltage: 4.5V - 5.6V 4.5V - 5.6V
Operational Current: 350mA 350mA
Type-C Voltage: 0V - 28V (for comparision, Type-C specs are 5 to 20V) 0V - 28V (for comparision, Type-C specs are 5 to 20V)
Type-C Current: 0 - 5A 0 - 5A
Type-A Current (Source): 0 - 1.5A when Type-C Voltage = 5V, 0 - 0.3A when Type-C Voltage > 5V 0 - 1.5A when Type-C Voltage = 5V, 0 - 0.3A when Type-C Voltage > 5V
Accuracy (V) Type-C port: 1% before calibration, 0.25% after calibration (Note 1) 1% before calibration, 0.25% after calibration (Note 1)
Accuracy (A) Type-C port: ±10mA for the entire range (0-5A), calibration improves the accuracy to 1% (Note 1) ±10mA for the entire range (0-5A), calibration improves the accuracy to 1% (Note 1)
Case: Aluminium - Black Anodized Aluminium - Black Anodized
Size: 140mm x 120mm x 75mm
(5.5 x 4.7 x 3 inches)
140mm x 120mm x 75mm
(5.5 x 4.7 x 3 inches)
Weight: 570g (20.1oz) 570g (20.1oz)
Safety Protections: Over current protection
Over voltage protection (up to 30V)
ESD Protection on USB2 data lines (IEC 61000-4-2 level 4, ±15kV contact discharge, ±20kV air discharge)
Short circuit protection
Isolated USB Monitoring port (1kv)
Heatsink temperature monitor
Over current protection
Over voltage protection (up to 28V)
ESD Protection on VBUS (IEC 61000-4-2 level 4, ±8 kV contact discharge, ±15 kV air discharge)
ESD Protection on USB2 data lines (IEC 61000-4-2 level 4, ±15kV contact discharge, ±20kV air discharge)
Short circuit protection
Isolated USB Monitoring port (1kv)
Heatsink temperature monitor
Storage Temperature: -30 ºC to + 80 ºC -30 ºC to + 80 ºC
Usage Temperature: 0 ºC to 35ºC (lower temperature allows longer period of higher loads) 0 ºC to 35ºC (lower temperature allows longer period of higher loads)
Part number: PM110 PM125
RoHS (Lead free): Yes Yes
Calibration Process: Return to Factory Return to Factory or On site by user

1. Calibration service is available upon request for an additional fee.

The specifications above are for the PassMark USB Power Delivery Tester hardware revision 001.

Cabling

Each device comes with 3 cables:

  • A 1 meter (39inch) USB B (male) to USB A (male) cable. This cable is used to connect the tester to a PC.
  • A 40cm (15inch) E-Marked 5A USB Type-C TO Type-C cable. This cable is used to connect the tester to a Type-C USB power source (USB port or wall charger).
  • A 40cm (15inch) USB TYPE-C TO USB A (male) cable. This cable is used to connect the tester to a Type A USB power source (USB port or wall charger).

Compatibility

Windows 7, 8, and 10 are supported.
Windows: USBPDTest software is required for Windows.
Both 32bit and 64bit Windows drivers are available.

Please contact sales@passmark.com for more ordering details.