PassMark Software

Announcement

Collapse
No announcement yet.

PCIE test card causes BSOD

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • PCIE test card causes BSOD

    Hi,

    We are using Burn In v8.1 and PCIE test cards to stress the PCIE interface.
    The interposer card is the EVM of DIODES PI7C9X2G606PR (https://www.diodes.com/products/conn.../PI7C9X2G606PR)

    After running for 5 hours, Windows 10 64bits happened BSOD (refer to attached pictures)

    Does anyone have ideas about this behavior?

    Thanks,
    Mark.
    Attached Files

  • #2
    The version of BurnInTest you are using is old. Can you try with V9.

    When were these cards purchased? What firmware release are you using?
    What device driver release are you using?
    Is the problem reproducible? If yes, does it always happen after 5 hours?
    Did you get a crash dump from the BSOD? Your photo indicated that it was a driver fault. But didn't indicate which driver.

    We have never done any testing with the EVM of DIODES PI7C9X2G606PR extender card.

    Comment


    • #3
      Okay, I would like to confirm the setup first.

      Attached photo is the card I used.
      I consider my card should use PCIe Test Card device driver (Old release for Firmware V1.8 ), correct?
      Before I was using PCIe Test Card device driver (For Firmware V2.0) on it.

      Today I change driver to the old one.
      But I can't run PCIE test item.
      The behavior is weird.
      Before I run Burn In test, it can detect those cards.
      After I run Burn In test, it CAN'T detect those cards.

      Is there anything wrong on my side?
      Thanks.

      Comment


      • #4
        The version of BurnInTest you are using is old. Can you try with V9.

        Are you sure you have the V1.8 firmware? There were not many units sold with that older firmware release. Can you post the log from the PCIeTest software.
        https://www.passmark.com/ftp/PCIeTestV2.0.1001.zip


        Comment


        • #5
          I tried Burn In v9.
          PCIE and ethernet advance test does not work. (CPU/RAM test does work)
          It keeps pending. no progress....

          I run PCIe test alone by installing new and old driver.
          I think it should be v2.0.....do you agree?
          Attached Files

          Comment


          • #6
            From the log file, it seems you have the V2.0 firmware. So please make sure you are using the latest driver and test application.
            https://www.passmark.com.au/download...t_download.htm

            The short run in the PCIeTestLog_new driver.txt seems to be fine, without error.

            Is the 5h crash problem reproducible? If yes, does it always happen after 5 hours?
            Can you send the crash dump file for further investigation?

            Comment


            • #7
              I'd like to confirm Burn In v9.0 test problem first.
              I can't run the test successfully.

              PCIE and ethernet advance test does not work. (CPU/RAM test does work)
              It keeps pending. no progress.... (please refer to attached photo)

              I use below conditions...
              OS: Win 10 64 bits
              Test SW: Burn In v9.0
              Test fixture: Pass Mark PCIE test cards (FW 2.0, according to your check)
              Driver: PCIe Test Card device driver (For Firmware V2.0)

              Comment


              • #8
                In the screen shot the test was only running for 30 seconds. And there appears to be some activity on the PCIe test. So I am not sure why you are saying there was no progress.

                If it is just the networking test that has the problem, what settings are you using for the network test.

                Comment

                Working...
                X